
Aro-Bond 949 is a single component moisture curing polyurethane adhesive. It has been developed specifically for applications in the panel manufacturing and laminating industries.
Need help?
Call us on 0117 971 1364 or click the button below.
Aro-Bond 949 is a simgle component moisture curing polyurethane adhesive. It has been developed specifically for applications in the panel manufacturing and laminating industries.
Aro-Bond® 949 can be used for many applications where gap filling properties, high strength and a high level of water resistance is required. Aro-Bond® 949 has been successfully used for bonding many types of woods, plastic foams and other insulating materials to a wide variety of both rigid and flexible facing materials, including wood, metals and plastics.
Ensure that the surfaces to be bonded are clean and free from dust, frease and other contaminants.
Metals should be stored in a warm environment, prior to bonding, to avoid chilling of the glue-line (which can lead to extended cure times).
The adhesive should be applied evenly over one side of each glueline using a mechanical roller coater, hand-roller or notched trowel. The amount applied will vary according to the porosity of the substrates, but will normally be in the range of 100-125gsm.
After application of the adhesive, a fine mist of atomised water must be applied to the adhesive. The amount required being approximately 10% of the weight of adhesive. The surfaces to be bonded should then interface as quickly as possible to minimise water evaporation, and placed under pressure within the open-time of the adhesive. The pressure required will depend on the nature of the substrates being boned - but is usually in the range of 0.5 to 0.9bar.
Pressure should be maintained, until the adhesive is sufficiently cured to permit handling of hte bonded item. Full cure of the adhesive is not obtained for 24 hours and handling within this period should be kept to a minimum.
Aro-Bond® 949 when uncured can be removed with cleaning solvent such as Aro-Bond® Solvent 6. Cured product will prove very difficult to remove, however, soaking in Aro-Bond® 6 Solvent overnight will soften the adhesive. Nozzles from automatic bead applicators should be immersed in a non-reactive plasticiser when not in use.
Aro-Bond® 949 is a moisture sensitive adhesive and left in contact with the open atmosphere will eventually gel. For this reason Aro-Bond® 949 is protected with a blanket of Nitrogen in the drum prior to despatch, which forms a dry, inert layer on top of the adhesive. Aro-Bond® 949 should be stored in the original containers in a cool, dry place, at a temperature range of between 5°C and 25°C. In these conditions it has a storage life of at least 3 months.
Once the container has been opened for use and the inert blanket replaced by moist air, the adhesive will have a limited life. To eliminate the moist air reacting with the adhesive a Nitrogen cylinder can be connected to the small bung hole of the drum, via suitable pressure reducing valves to give a positive pressure of 1 -2 psi.
Alternatively a desiccator can be connected to the small bung hole of the drum, which will dry the incoming air, replacing the adhesive used. A suitable desiccator with the relevant pipework can be supplied by Alansons. This will last for approximately 3 months prior to regeneration. Further information is available upon request.
If water enters the drum of adhesive, it will react giving off carbon dioxide which can cause over pressurisation of closed cans and drums.
The product should be stored un-opened in a dry condition at a temperature of 5-250C. this will ensure the stated shelf-life. The adhesive will have a limited life once the container is opened.
There are no reviews for this product.
Click the button above to ask a question.
Aro-Bond 949 GP MCPU Roller Coatable Adhesive Safety Data Sheet
Aro-Bond 949 GP MCPU Roller Coatable Adhesive Technical Data Sheet
Use our adhesive coverage calculator to find out how much you need for your project.
Based on your m2 you need:
kg of Aro-Bond 949 GP MCPU Roller Coatable Adhesive.
Including 10% wastage.
1kg of Aro-Bond 949 GP MCPU Roller Coatable Adhesive covers 10m2. You require enough product to cover m2 including 10% wastage. m2 / 10m2 per kg = kg of product.
Use our adhesive coverage calculator to find out how much you need for your project.
Based on your m2 you need:
kg of Aro-Bond 949 GP MCPU Roller Coatable Adhesive.
Including 10% wastage.
1kg of Aro-Bond 949 GP MCPU Roller Coatable Adhesive covers 10m2. You require enough product to cover m2 including 10% wastage. m2 / 10m2 per kg = kg of product.
Got an adhesives problem? Let our sticky smarts work for you.
Call us0117 971 1364
Email ussales@thenamethatsticks.com
Get how-to advice, industry news and new innovations — straight to your inbox.